汽车机油如何换？ 自己如何换汽车机油？英文双语对照

汽车机油如何换？

1. 热车预备：先将车子发动起来，让发动机里的机油热一下，流动性比较好，也更容易放得干净。建议热车时间约为10分钟左右。

2. 接下来需要将车辆举升起来，如果是轿车底盘比较低，建议使用专门的举升设备。而SUV则比较容易爬进去，就不需要做这一步了。

3. 找到机油底壳：机油底壳一般位于发动机正下方，是一个金属盖子，上面有字样 "Oil" 或 "Engine Oil"。

4. 用扳手卸下机油底壳，注意用手套避免被机油烫伤。在拆卸过程中，要注意机油的流出口与接口，以免弄混。

5. 将机油底壳完全卸掉之后，让机油自流至少10分钟，尽量排尽废油。建议等待更久，直到底壳处看不到滴落的机油。

6. 更换机油滤芯，滤芯一般位于机油底壳上方，用扳手拆下即可。拆卸前一定要检查滤芯的型号，购买时选择与原车相同型号的机油滤芯。

7. 重新安装新的机油滤芯。包括将其装回内盖及外盖及用手按压至到位即可。

8. 放入新机油，加油之前请确认机油标签上标明车辆使用的机油型号和容量，并以此为准。在向发动机注入机油时，慢慢地倒入，不要一次性倒入所有机油。在倒油过程中，注意观察机油量计的指示，确保没有超过最大液位线。

9. 检查机油底壳是否已正确固定，确保被接口塞子已经被拧紧。最后，启动发动机，热车2~3分钟，然后再关掉，检查机油的液位是否在合适位置。

自己如何换汽车机油？

1、换机油前先把车子发动起来，热车个10分钟左右，发动机里面的机油热一下流动性比较好，也更容易放得干净。接着就是把这个车子举升起来，轿车底盘比较低，爬不进去也就没有办法换了，SUV的话直接爬进去就不需要做这一步了。这里倒是不建议各位朋友用千斤顶把车子顶起来，它是有危险的，万一滑一下边上有人推一下这个车子压下来怎么办对吧？最好是用这种坡道板比较方便也比较安全，直接开上去就搞定了。

2、然后爬到车底找到放油螺丝，放油螺丝一般都在油底壳上面，是上面最大的一颗螺丝，还是比较容易发现的。如果你不知道哪个是油底壳，你只要打开发动机舱找到发动机的位置，油底壳云般就在发动机的最底下，不过有些车子是有发动机护板的，那先要把它拆掉才能看到放油螺丝，放油螺丝一般需要19号的拔手，提前准备好抗螺丝前记得带好手套，同时在底下放一个桶或者脸盆来接放出来的旧机油，还有就是把加油加注口的盖子打开，这样可以利用大气压强的原理让机油很顺畅的流出来，这些都做好之后，这个时候旧机油就是从放油螺丝孔里面流出来了，你等它放完就行。放完机油之后到是不建议把旧的放油螺丝再回去，因为有很多车子它放油螺丝的垫片它是金属的，用过一次之后就变形了，最好是换新的垫片或者是新的放油螺丝，这样可以降低漏油的风险，很多维修店不管这些东西的，就的直接给你装回去完事的，你是新车不要紧的，所以自己来上心一点，好处就在这了。

3、新的放油螺丝装好扩回去接着换滤芯，这台朗逸的机油滤芯是在油底壳上面的，有些车子是在发动机舱里面的，换之前的话可以看一下手册或者是直接打开来看一下，换机滤需要专门的换机滤拔手，用手的话就需要大力出奇迹了，机滤板手逆时针把机滤松，然后用手把机滤来就可以了，也是会有机油漏出来的，而且机滤里面也会残留机油，拿的时候注意点不要倒过来，接着机滤附近擦干净。

汽车机油滤芯怎么换？

机油滤芯的更换步骤：

1.首先用汽车升降架将爱车升起来。

2.然后打开底部的机油口，观察漏出来的机油是不是显黑色的，如果是的话就需要及时更换机油了。

3.随之就可以用专门的扳手打开机油滤芯了，要知道机油口的流速是很慢的，可以在这时候打开滤芯进行二次释放。

4.最后当机油全部流干净之后，使用扳手将新的机油滤芯装上去就大功告成了。当然还得往机油口倒入符合规格的机油（适量即可）。

汽车换什么机油好？

尽量选择多级油，多级油由于节省、寿命长、高效，对发动机有较好的保护作用。基于多级油的特

性，在使用过程中可能会出现过早发黑、机油压力较普通机油小的现象，均系正常。

1.全合成机油:全合成机油有更好的高低温性能，有更长的换油周期以及适合更恶劣的用车情况，适合豪华高性能车使用，10000-12000公里左右更换。

2.半合成机油:半合成机油的更换周期一般是在8000-10000公里左右，价格与性能适中。

3.矿物机油:这类型机油一般在5000公里左右就需要更换。

汽车保养换什么机油？

当然最好是全合成机油。质量好，耐用。只是价格偏高。粘度和最低使用温度根据自己所在地区实际情况选用。

汽车机油多少毫升 换？

保养一次大概需要200毫升的机油，这并不固定，不同的发动机保养所需要的的机油量不一样。保养用机油的量要以汽车的发动机机油尺检车的标准为准。

更多相关资料如下：1.要想知道保养一次车需要使用的机油的量可以把先把机油尺拿出来，机油尺的表面会有一处凹凸不平的地方，而看机油的位线就是依据机油尺凹出会有花格。2.机油尺凹处还有上下的横线，然后再把机油尺插入。保养车时机油在花格线上下范围之内即可，不易过少，也不易过多。

汽车机油杯怎么换？

1、准备好新机油和机油滤清器，并准备容器接旧机油。

2、运转发动机，使其达到工作温度，热机条件下拧开机油盖，在拧下机油底壳的放油螺丝放出旧机油，多放一会旧机油。

3、拧下旧机油滤清器 是不循环使用的

4、在新滤清器胶圈上抹一点机油，然后拧紧

5、将放油螺丝拧紧 通常是拧紧后再拧3、4圈

6、将新机油倒入油底壳之后，反复察看机油尺加油 注意别撒到外面 可以用漏斗 加适当量后 将机油盖拧紧

7、启动发动机运转2至3分钟后熄火，然后观察放油螺丝，机油滤清器是否有渗透

8、熄火10分钟后，再观察机油尺机油面，已接近上限为宜。

9、最后根据当地法规处理旧机油和滤芯

汽车循环机油怎么换？

机油着车就是循环的，换机油拆下油底放油罗母，放干净后扭紧放油罗母，加上新机油就行，记得同时换机油滤芯。

烧机油的汽车换什么机油好？

我的迈腾b6，17万多公里，一点不烧机油。

一点经验就是用高粘度、高品质的机油，我用0W40的进口GT机油，PAO类的保护性能最好，还有一点是，机油性能是随着公里数增加而降低的，机油衰减了就要及时更换。

如何看汽车机油标尺？如何看汽车机油标尺？

步骤：

1。首先打开主驾驶门，找到打开汽车引擎盖的开关，一般在主驾驶的内侧，然后到引擎盖前面找到前开开关。

2.打开发动机罩后，举起支撑杆。有些高档车是液压支撑杆，不用人工操作就能抬起来，然后找到油表位置。一般都是色标环扣。

3.拉动黄色拉环，用力拉出，直到全部拉出。这把尺子又长又软，可以弯曲。

4.仔细看标尺正面有两个缺口，右边缺口是最低油位，左边缺口是最高油位。

5.为了便于检查，先用餐巾纸或抹布擦拭。

6.将擦拭后的油量表重新放回原位，然后再次拉起。你会发现这是油位，刚好在两个刻度尺之间就可以了。

---

英文翻译对照，仅供参考

---

How is car engine oil changed?

1.Hot car is preliminary: Launch the car first rise, make the engine oil in engine hot, liquidity is better, put more easily also neatly. Suggest hot car time is about 10 minutes or so.

2.Next need cites traffic rise, if be car batholith lower, the proposal is used move litre of facility technically. And SUV climbs in more easily, do not need to make this one step.

3.Find case of engine oil base: Case of engine oil base is located in engine commonly lower part, it is cap of a metal, there is "Oil of model of written characters above"Or "Engine Oil" .

4.With case of base of spanner debus engine oil, the attention avoids with the glove by engine oil scald. Disassembling in the process, want those who notice engine oil to pour out of mouth and interface, lest mix.

5.After case of engine oil base complete discharge is dropped, let engine oil do as one pleases at least 10 minutes, discharge useless oil as far as possible. The proposal awaits longer, cannot see drippy engine oil till base case department.

6.Change core of engine oil filter, filter core is located in upper part of case of engine oil base commonly, tear open with spanner below can. The type of filter core must be examined before disassembling, the core of engine oil filter of as same as primary vehicle type chooses when buying.

7.Reinstall core of new engine oil filter. Include to install its inside build the lid outside reaching to reach press with the hand press to reach the designated position can.

8.Put new engine oil, before cheering, affirm to the engine oil model that car uses and capacity indicate on engine oil label please, it is with this accurate. Be in to engine infuse engine oil when, fall slowly, not one-time enter all engine oil. In oily process, the attention observes engine oil the directive of quantity plan, ensure did not exceed the biggest fluid line.

9.Whether is case of base of examination engine oil secured correctly already, ensure had been screwed by interface plug. Finally, the engine that start, hot car 2~3 minute, put out again next, the fluid that checks engine oil whether be proper place.

How do oneself change car engine oil?

1, before changing engine oil, launch the car first rise, hot car 10 minutes or so, the engine oil inside engine heats up fluidity to had been compared, put more easily also neatly. Catch even if start this car rise, car batholith is lower, climb to did not go in to also be changed without method, the word of SUV climbs in not to need to make this one step directly. Here does not suggest each friend uses car of hoisting jack holder-on to support however, it has risk, does the somebody on one below push ten thousand glance does this car pressing come down how to do be opposite? Had better be to use this kind of ramp board to go to the lavatory to also compare safety quite, leave directly go up to be done decided.

2, climb to find the screw that put oil to the end of the car next, the screw that put oil is in commonly by oil above housing, be above a the biggest screw, discover more easily still. If you do not know which it is oily base case, you should open engine cabin to find the place of engine only, be in like cloud of oily base case of engine most next, nevertheless some cars have engine fender, that should pull down it first ability sees the screw that put oil, put what oily screw needs 19 commonly to unplug hand, get ready ahead of schedule before fighting screw, remember taking good glove, fall in the bottom at the same time put a bucket or washbasin will receive the old engine oil that puts, still have even if cheer add the cap that notes a mouth to open, the principle that can use air intensity of pressure so makes engine oil very smooth flow, after these had been done, this moment old engine oil is flow from inside aperture of the screw that put oil, you wait for it to be put go. After putting engine oil, arriving is not to suggest to go back the old screw that put oil again, the spacer that because have very much car,it puts oily screw it is a metal, after been use, was out of shape, had better be to change the screw putting oil with new new perhaps spacer, can reduce the risk of leakage oil so, shop of a lot of maintenance no matter of these things, install those who come to an end to you directly, new car nevers mind you, so oneself go up heart a bit, advantage is in this.

3, the new screw that put oil installs good spread to go back to change filter core then, the core of engine oil filter of this Lang Yi is to be by oil above housing, some cars are in inside engine cabin, the word before changing can see manual perhaps be opened directly will look, change machine filter to need to change machine filter technically to unplug hand, the miracle goes out energetically with respect to need if using a hand, hand of machine filter plate is anticlockwise loosen machine filter, it is OK to come with handgrip machine filter next, also can organic oily leakage comes, and engine oil also can remain inside machine filter, when taking, notice the point does not come, catch machine filter around wipe up.

How is core of filter of car engine oil changed?

Of core of engine oil filter change measure:

1. rises with the car above all fall frame love the car rises.

2. opens bottom engine oil mouth next, the engine oil that observes leakage comes shows black, if be if change in time with respect to need engine oil.

3. can open core of engine oil filter with special spanner subsequently, wanting the velocity of flow that knows engine oil mouth is very slow, can open filter core to undertake 2 times releasing at this time.

After 4. flows clean entirely when engine oil finally, use spanner goes to mount of new core of engine oil filter with respect to success. The engine oil that returns so that pour up to specification toward engine oil mouth of course (right amount can) .

It what engine oil the car changes is good that what engine oil the car changes?

Choose multistage oil as far as possible, multistage is oily because economic, life is long, efficient, have better protective effect to engine. Those who be based on multistage oil is special

Quality, pressure of premature and nigrescent, engine oil may appear in using a process the phenomenon with commonner small engine oil, all be normal.

Does 1. synthesize engine oil: completely?

Does 2. synthesize engine oil: partly?  of cover with a straw mat of mill of an official document or note steals Kang of word of show off of Zhi of mother  extensive to steal?000-10000 kilometer left and right sides, the price and function moderate.

: of 3. mineral engine oil? Yu noise dash forward left and right sides of kilometer of?000 of  ostrich word tending or guard a gate changes with respect to need.

Does the car maintain what engine oil to change?

Had better be complete synthesis engine oil of course. Quality is good, durable. It is price on the high side only. Him basis of use temperature of viscosity and lowest is in an area actual condition is chosen.

How many milliliter changes car engine oil?

Maintain the engine oil that needs 200 milliliter probably, this is not fixed, different engine maintains of a need engine oil amount is different. Maintain the standard that wants the car of check of feet of engine engine oil with the car with the quantity of engine oil is accurate.

More and relevant data is as follows: 1. Want to know to maintain the quantity of the engine oil that the car needs to use is OK take engine oil foot first, the surface of engine oil feet can have one to manage uneven place, and reading a line of engine oil is feet of basis engine oil sunken piece can have beautiful case. 2. Sunken part of engine oil rule still has the horizontal line of fluctuation, insert engine oil rule again next. Maintain car opportunity oil is in limits of fluctuation of beautiful division line can, pass not easily little, not easy also and overmuch.

How is cup of car engine oil changed?

1, prepare new engine oil and engine oil filter, prepare container to receive old engine oil.

2, locomotive engine, make its reach working temperature, heat engine condition issues engine oil of to turn on to build, in the putting that twists the carapace end next engine oil oily screw discharges old engine oil, put old engine oil a little while more.

3, twisting filter of next old engine oil is not used circularly

4, in new filter glue encircles a bit engine oil, screw next

5, screwing the screw that put oil is normally after screwing, twist again 3, 4

6, after will new engine oil enters oily base case, after looking carefully at engine oil feet to cheer an attention to be not scattered to the outside to be able to increase proper amount with funnel repeatedly, engine oil the lid screws

7, the engine that start runs the 2 flameout after coming 3 minutes, observe the screw that put oil next, whether does engine oil filter have permeate

8, flameout after 10 minutes, observe face of engine oil of engine oil feet again, it is advisable to already approached upper limit.

9, handle old engine oil and filter core according to local code finally

How is car loop engine oil changed?

Engine oil wears what the car circulates namely, change engine oil to tear open bottom issueing oil to put oil collect nut, the screw after be being put clean puts oil collect nut, add new engine oil to go, remember changing core of engine oil filter at the same time.

It what engine oil the car that burns engine oil changes is good that what engine oil the car that burns engine oil changes?

My stride vacate B6, 170 thousand much kilometer, did not burn engine oil.

A bit experience uses tall viscosity, high quality engine oil namely, I use the entrance GT engine oil of 0W40, PAO kind protection can be best, still having a bit is, number increases and engine oil performance is reduced as the kilometer, engine oil attenuation be about to change in time.

How to see rear sight of car engine oil? How to see rear sight of car engine oil?

Measure:

1. Open above all advocate drive the door, discover the switch that opens car engine lid, be in commonly advocate driving inside, open switch to the front of be found before engine lid next.

After 2. opens engine cover, raise strut bar. A little high-grade car is hydraulic pressure strut bar, can not raise with artificial operation come, find oil to express the position next. It is color patch annulus is buckled commonly.

3. is pulled use maize ring tab, tug goes out, until pull entirely. This grows rule again soft, can bend.

Front of staff guage of 4. young scrutiny has two gap, right breach is lowermost oil level, left breach is top oil level.

5. is checked to facilitate, use napkin or dishcloth to wipe first.

The oily relay measuring a watch after 6. will be wiped is answered former, pull again next. You can discover this is oil level, just be between two scale feet is OK.