大自然地板售后流程？ 木地板安装流程？英文双语对照

一、大自然地板售后流程？

一、零资费送货：市区内免费送货。

二、零付费保养：地板安装后免费为保养1次。

三、实施保修服务、终身维护政策：实木地板、实木复合地板、生态复合地板、仿实木强化木地板质量保修1年，提供终身维护与保养服务咨询。

大自然地板售后服务

四、实施全国800免费服务热线，至真至诚为客户服务。

五、实施48小时内到达现场勘察，在勘察后的三个工作日内与客户协商解决方案。

六、实施客户档案查询系统：为购买大自然地板的客户建立客户档案，进行1对1跟踪服务。

七、实施产品防伪查询系统：建立产品防伪查询系统，让消费者可以放心购买大自然地板。

八、100%透明专业安装：根据各地不同铺装环境及客户要求进行透明报价专业安装。

九、360°保养服务：对购买大自然地板的客户提供保养咨询和专业保养，使用大自然地板专用保养产品。

二、木地板安装流程？

步骤1：前期筹备

一、安装木地板以前，应当维持地面平整干燥，清楚地面上的所有杂物。

二、要注意木地板安装必需在其它装修工程完工后方可进行。

步骤2：铺设龙骨

一、在木地板铺设的反方向，弹出龙骨的铺装路线，并用电锤依照三0cm的间距进行打眼。

二、必需维持龙骨干燥，含水率不患上超过一五%。千万不能使用水泥进行堆埋。针对于不平整的龙骨必需使用罗纹防松地龙专用钉进行刨平处理，确保龙骨平整牢固以后，才能开始进行铺设。

三、在木龙骨的4周以及中央部份，放1些木地板专用防蛀剂进行防虫，还要在木龙骨上铺设1层防潮膜，以防木地板受潮变形，要注意在防潮膜的接口处互叠一0cm。

步骤3：试安装木地板

一、因为木地板材质天然，在色泽以及纹理上会有所差异，因而，在安装前1般都要进行总体试铺，并依据木地板的纹理以及色彩公道调剂色差，使总体铺装效果更自然融洽。

二、对于于收边、错缝等处需要的木地板，应事前进行搭配，充沛应用材料，减少消耗。

步骤4：正式安装木地板

一、因为木地板在使用进程中容易遭到湿度、温度等气候因素的影响而发生轻微的缩胀，在安装木地板时，要依据不同地区的气候前提适量预留伸缩缝。

二、安装时在墙角的4周应留出一0摆布的伸缩缝，用地板钉将每一块地板斜向四五°固定在龙骨上。

三、如果所处地区尤其湿润，安装地板时，相邻两块地板之间尽可能不要靠太紧，以避免受潮变形。在气候干燥地区，地板之间以自然结合为准。

四、如果木地板安装的距离太长，北方地区大于八m，南方地区大于六m，最佳加设过桥隔断。

五、在房间、厅堂之间接口处，应断开木地板，留有一0—一二的伸缩缝，用收口条进行衔接。

三、大自然木地板的工艺流程？

大自然实木地板的铺设要点（1）地板应在施工后期铺设，不得交叉施工。铺设后应尽快打磨和涂装。以免弄脏地板或使受潮变形。

（2）地板铺设前宜拆包堆放在铺设现场1～2天，使其适应环境，以免铺设后出现胀缩变形。

（3）铺设应做好防潮措施，尤其是底层等较潮湿的场合。防潮措施有涂防潮漆、铺防潮膜、使用铺垫宝等等。

（4）龙骨应平整牢固，切忌用水泥加固，最好用膨胀螺栓、美固钉等。

（5）龙骨应选用握钉力较强的落叶松、柳安等木材。

龙骨或毛地板的含水率应接近地板的含水率。

龙骨间距不宜太大，一般不超过30厘米。

地板两端应落实在龙骨上，不得空搁，且每根龙骨上都必须钉上钉子。不得使用水性胶水。

（6）地板不宜铺得太紧，四周应留足够的伸缩缝（0.5～1.2厘米），且不宜超宽铺设，如遇较宽的场合应分隔切断，再压铜条过渡。

（7）地板和厅、卫生间、厨房间等石质地面交接处应有彻底的隔离防潮措施。

（8）地板色差不可避免，如对色差有较高要求，可预先分拣，采取逐步过渡的方法，以减少视觉上的突变感。

（9）使用中忌用水冲洗，避免长时间的日晒、空调连续直吹，窗口处防止雨林、避免硬物撞摩擦。

为保护地板，在漆面上可以打蜡（从保护地板的角度看，打蜡比涂漆效果更好）。大自然实木地板如何打磨1、找准实木地板存在哪些问题，比如局部开裂、严重划伤、小范围起拱等，清楚地板上的杂质保持整洁。

2、开始使用大型地板翻新机械打磨地板，准备四种不同砂纸，先用粗砂打磨，除去漆层、表层、木质层约0.5毫米，再用细砂打磨地板至表面细腻光滑，达到全新状态。

周围边角的地方应用专门的边角小型角磨机打磨，必要的时候还得手工操作。

3、将原有的边缝透明腻子清楚干净，在涂上新的腻子层。开裂的地方涂上粘胶剂或用木块填上封闭，起拱的地方用钉子定住，避免以后再出问题。

四、大自然地板安装怎么算平方？

1 以地砖的大小来计算，长乘以宽，比如：600的地砖，其平方面积为：0·6 米× 0·6米=0·36平方米，即每匹地砖的平方为0·36平方米，以总的地砖匹数乘以每匹地砖的平方即为总的平方数。

2 以所要粘贴地砖的地平方计算：地面的长乘以宽，比如：所要粘贴的地平方为：12米×16米=192平方米，如果是计划地砖数量，应该外加损耗。

五、工装木地板安装流程？

工装木地板的安装流程主要包括以下几个步骤：1. 准备工作：测量房间的尺寸，确定所需木地板的数量，并将木地板置于室内进行适应环境的处理。2. 清理底层：将房间内的旧地板或其他底层材料清理干净，确保地面平整，无垃圾和尘土。3. 铺设隔音膜：铺设隔音膜，以减少噪音和增加地板的稳定性。4. 安装木地板：根据所选的安装方式（例如锁扣式、粘贴式或钉扣式），按照从房间的一侧开始铺设木地板板块，逐渐向另一侧铺设。5. 切割与拼接：在需要的地方，使用锯子或电锯将木地板材料进行切割，以适应房间的形状和尺寸。将切割的地板板块与原始的板块拼接在一起。6. 固定和固定地板：根据所选的安装方式，使用胶水、钉子或螺丝将地板板块固定在底层上。确保地板板块牢固地固定在底层上，并与相邻的板块平齐。7. 完善细节：安装完毕后，仔细检查地板的整体平整性和装饰效果，进行必要的调整和修正。填补地板板块之间的缝隙，并处理地板的边缘和角部，使其看起来整洁美观。8. 清理和保养：最后，清理地板周围的杂物和垃圾，并进行地板的基础清洁。根据木地板的材质和要求，进行适当的保养和维护，以保持地板的良好状态。注意：以上是一般的工装木地板的安装流程，并可能因具体情况而有所不同。在进行安装前，最好咨询专业的地板安装公司或相关专业人士，以获得准确的指导和建议。

六、复合木地板安装流程？

一）准备工作

1、清洁地面

在准备铺设木地板的区域，做好清洁，保证房间的角落没有灰尘。

2、地面找平

若是地面凹凸不平，就直接铺木地板，在后期极容易出现起翘的问题。在找平时，要注意水平误差要控制在2mm以内。

3、地板处理

地板的铺设方式不同，导致所需的大小各有差别，因此要根据空间的需求来切割复合地板。

4、预留踢脚线位置

要先将踢脚线的位置预留出来，通常情况是会在踢脚线的位置上，放上等厚度模板。

（二）复合地板的安装

1、地板拼接

拼接木地板需对准、压平。确保地板间不产生空隙。铺满整个房间即可。

2、测量踢脚线长度

各个房间区域所需要用到的踢脚线长度不等，因此需要测量好各个地方所需要用到的长度。

3、踢脚线的切割

在确定好区域所需的踢脚线长度后，将其切割。

4、踢脚线的安装

将踢脚线卡进预留的缝隙之中。

5、踢脚线接头处理

在切割踢脚线时，需将两端做成相称的形状，这样以利于将不同的两端连接在一起。

6、固定踢脚线

将地板钉固定踢脚线，使之固定，不易松脱。

七、实木地板安装流程？

1、地面处理

在安装实木地板时，我们可以先用水平尺检查地面是不是平整，如果地面不平，大家可以将水泥砂浆或自流平配置好，将其涂抹在地面上进行找平。地面找平后，我们还需检验地面的平整度，并将地面上的杂质清理干净。

2、地面画线

实木地板可采用龙骨铺设的方式，在施工时我们需先在地面上弹出龙骨的铺设位置。大家可以根据木地板的铺设方向、长度、龙骨之间的间距等进行地面画线。一般一块木地板需3根龙骨，龙骨之间的间距不可超过350毫米。

3、铺设龙骨

大家用电钻在地面上进行打孔，其打孔深度通常25毫米以上。接下来我们用钉子把龙骨固定在地面上。在铺设龙骨时，龙骨和墙面之间需留有5-10毫米的间距。龙骨铺设好之后，我们还需检查龙头是不是平整牢固。如果房子比较潮湿，龙骨铺设好之后，我们可在龙骨上铺上一层防潮膜。

4、铺设实木地板

我们可以先对实木地板进行试铺，将略有色差的地板放在房间不显眼的地方，并且对实木地板进行剪裁。接下来我们将实木地板铺设在龙骨上，并用气钉枪将地板钉牢固。地板要采用错位铺设的方式，并且每铺设3-5块木地板就需要检查下地板有没有铺平直等等。

5、铺设踢脚线

木地板铺好之后，我们在墙面上进行钻孔并塞入木楔，接下来将踢脚线裁剪好，并将其放好用钉子将其固定在墙面上。

八、威然地板安装流程？

威然地板的安装先做好地板筋，做好防潮防蛀保护，打扫卫生干净安装地板

九、大自然木地板必须安装脚线吗？

大自然木地板是需要安装脚线的，美观，防松动。

十、69元大自然地板包安装吗？

不包安装，正常安装费就需要30元每平

大自然实木地板安装的费用:费用包括了人工费,一般是12元;实木地板安装费用等于实木地板的价格乘以面积来计算的;地板铺设以及踢脚线的安装,每平方米大概3元钱左右,另外,踢脚线采用的材质如果是实木的话,价格从10-60元不等,比较常用的是在20-30元之间。

One, the flow after nature floor makes work?

One, deliver goods of 0 endowment cost: Inside the urban district free deliver goods.

2, 0 pay cost to maintain: After the floor is installed it is freely maintain 1 times.

3, carry out guarantee service, lifelong maintain policy: Real wood floor, solid Mu Fu adds up to floor, zoology quality of floor of wood of aggrandizement of real wood of compound floor, copy guarantees 1 year, offer lifelong safeguard with maintain the service seeks advice.

Nature floor after service

4, 800 free service hot lines of executive whole nation, serve for the client to true complete sincerity.

5, carry out spot reconnaissance arrives inside 48 hours, 3 jobs after reconnaissance negotiate a solution with the client in a few days.

6, executive client archives inquires a system: Establish client record to buy the client of nature floor, undertake 1 pair 1 dog service.

7, executive product prevents bogus to inquire a system: Build a product to prevent bogus to inquire a system, make consumer OK be at ease buy nature floor board.

8, 100% transparent major install: According to each district different shop installs environment and client demand to undertake transparent quote major is installed.

9, 360 ° maintain service: Maintain to buying the client of nature floor to offer seek advice to maintain with major, use nature floor board is special maintain product.

2, does wooden floor install flow?

Measure 1: Early days is prepared

One, before installation wood floor, ought to maintain ground level dry, clear ground is all and sundry.

2, should notice wooden floor installation is indispensible the project is decorated in other finishing and rear can undertake.

Measure 2: Laid keel

One, in wooden floor laid return way, the shop that plays a keel holds a line, use electric hammer according to the span of 3 0cm undertakes punching a hole.

2, indispensible maintain dragon backbone dry, moisture content does not suffer from on more than one. Ten million cannot use cement to undertake piling burying. In the light of at rough whole keel needs use Luo Wen prevents loose earthworm special hammer undertakes plane is handled, after ensuring keel level off is firm, ability begins to undertake laid.

3, 4 weeks in wooden keel and the part central, put floor of 1 some of wood special moth-proofing agent undertakes insect-resistant, set a moistureproof film in wooden keel upper berth even, in case wooden floor be affected with damp be affected with damp is out of shape, want to notice the interface in moistureproof film is in each other to fold one 0cm.

Measure 3: Try installation wood floor

One, because wooden floor material is qualitative natural, meet on colour and lustre and grain somewhat difference, consequently, before installation 1 kind should undertake overall try a store, regulate off color according to the grain of wooden floor and colour justice, make effect of overall shop outfit more natural and harmonious.

2, the wooden floor that handles need to waiting at receiving edge, fault to seam, should beforehand undertakes collocation, abundant application material, decrease use up.

Measure 4: Install wooden floor board formally

One, suffer the climate element such as humidity, temperature easily in use process because of wooden floor affect and happen to shrink slightly bilge, when installing wooden floor board, want the climate premise according to different area right amount obligate is adjustable seam.

2, the in the corner 4 Zhouying put apart when installation one 0 those who order about is adjustable seam, nail with the floor each floor inclined secure to 45 ° go up in keel.

3, if located area especially wet, when installing a floor board, photograph adjacent does not lean as far as possible between two floors too close, be out of shape in order to avoid be affected with damp be affected with damp. In climate dry area, it is with be united in wedlock naturally between the floor accurate.

4, the distance that installs like fruit tree floor is too long, northern region is more than 8 M, southern region is more than 6 M, optimal add had set bridge partition.

5, between hall of room, hall interface is in, should disconnect wooden floor, stay have one 0, of just a little adjustable seam, with receive pig's or ox's tongue to undertake joining.

3, the technological process of nature wood floor?

The laid point of floor of nature real wood (1) the floor should be in laid of construction later period, do not get alternate construction. Answer after laid as soon as possible burnish and besmear outfit. Lest flyblown floor or make be affected with damp be affected with damp is out of shape.

(2) the appropriate before floor laid tears open a bag to pile up in laid spot 1 ～ 2 days, make its acclimatization, lest appear after laid,bilge shrink be out of shape.

(3) laid should have made moistureproof step, especially the damper circumstance such as ground floor. Moistureproof measure has besmear to prevent wet lacquer, shop treasure of moistureproof film, use matting is waited a moment.

(4) keel should level off is firm, avoid by all means uses cement consolidate, had better use expand hammer of bolt, beautiful solid.

(5) keel should choose the lumber such as the deciduous leaf pine with the more powerful force that grasp a hammer, Liu An.

The moisture content of keel or wool floor should be close to the moisture content of the floor.

Keel span shoulds not be too big, do not exceed 30 centimeters commonly.

Two end should fulfil the floor to go up in keel, must not put aside for nothing, and must nail on every keel on nail. Do not get glue of use ability in swimming.

(6) unfavorable shop gets the floor board too close, should stay all around enough adjustable seam (0.5 ～ 1.2 centimeters) , and unfavorable exceed wide laid, if encounter wider circumstance part of one's job to lie between,cut off, press copper again transfer.

(7) the face of stone quality of a material such as room of floor and hall, toilet, hutch hands over the segregation with due and proper place moistureproof measure.

(8) floor chromatism is inevitable, if have higher demand to off color, but beforehand sorting, adopt the method that transfers stage by stage, in order to reduce the choppy feeling on the vision.

(9) the avoid in using is rinsed with water, avoid long insolation, air conditioning to be blown continuously continuously, window place prevents rain forest, avoid good thing to bump into attrition.

To protect a floor board, can wax on lacquer face (look from the point of view that protects a floor board, waxing is better than lacquer effect) . Floor of nature real wood how burnish 1, look for floor of accurate real wood to exist what problem, for instance local craze, serious cut, little scope removes arch to wait, the impurity on clear floor keeps neat.

2, begin to use large floor board to renovate mechanical burnish floor, prepare 4 kinds of different sand paper, use thick arenaceous burnish first, layer of eliminate lacquer layer, surface layer, woodiness makes an appointment with 0.5 millimeter, floor of fine arenaceous burnish reachs reoccupy the surface is exquisite and slick, achieve brand-new condition.

Small-sized horn grinds the horn side the local application of horn of week surrounding edge is special machine burnish, necessary when operation of procurable still labour.

3, will original edge seams transparent be bored with child clear and clean, new on besmear be bored with child layer. The place of craze sticks glue agent on besmear or fill with block on close, the place that has wriggle through the earth stays surely with nail, avoid to give an issue again later.

4, how does nature floor installation calculate square?

The 1 bulk with floor tile will calculate, long multiply with wide, for instance: The floor tile of 600, its make the same score square area to be: 0 · 0 · of 6 meters of × 36 square metre of · of 6 meters of =0, namely the square of every floor tile is 0 · 36 square metre, with total floor tile be equal to number is total smooth number of squares namely by the square with every floor tile.

The 2 n that want stickup floor tile with place just calculate: The length of the ground is multiplied with wide, for instance: What want stickup ground square to be: 12 meters of × square metre of 16 meters of =192, if be amount of plan floor tile, should adscititious loss.

5, does tool wood floor install flow?

The installation flow of tool wood floor basically includes the following measure: 1. Preparation works: Measure the size of the room, definite place requires the amount of wooden floor, and wooden floor park indoor the processing that undertakes acclimatization. 2. Clear rock-bottom: Clear the old floor board inside the room or other and rock-bottom material clean, ensure ground level, without rubbish and dust. 3. Film of laid sound insulation: Film of laid sound insulation, in order to reduce noise and the stability that increase a floor board. 4. Install wooden floor board: The installation way that picks according to place (for example lock type, stickup type or hammer buckle type) , begin laid wood floor board according to a side from the room board piece, gradually to another side laid. 5. Cut and joining together: Be in the place of need, use saw or electric saw wood flooring has cut, in order to get used to the appearance of the room and dimension. The floor cut board piece with primitive board piece joining together is together. 6. Secure and secure a floor: Install means according to what what choose, use sizy, nail or screw general floor board piece fixed go up in ground floor. Ensure floor board piece secure firmly go up in ground floor, and with photograph adjacent board piece smooth neat. 7. Perfect detail: After installation ends, the sex of integral level off of microscope floor and adornment effect, undertake necessary adjustment is mixed amend. Fill floor board piece the aperture between, handle the brim of the floor and horny ministry, make its look neat and beautiful. 8. Clear and maintain: Finally, clear all round the floor sundry with rubbish, the foundation of hand-in-hand travel floor is clean. Pledge according to the material of wooden floor and ask, undertake maintain and be maintenanced appropriately, in order to maintain the kilter of the floor. Attention: Above is the installation flow of general tool wood floor board, likely because of particular case differ somewhat. Before undertaking installing, the floor of best advisory major installs company or relevant and professional personage, in order to obtain accurate guidance and proposal.

6, does compound wood floor install flow?

One) preparation works

1, clean ground

Preparing the section of laid wood floor, do good cleanness, the corner that assures a room does not have dirt.

2, ground make level

If the ground is uneven, lay wooden floor directly, appear extremely easily in later period a problem that become warped. When make level, should notice horizontal error wants control to be in 2mm less than.

3, floor processing

The laid kind of the floor is different, bring about wants size to have a difference each, because this wants a foundation,dimensional demand comes cut is compound floor.

4, obligate plays crural line position

The positional obligate that wants to will play crural line first comes out, normally the circumstance is to be able to be in those who play crural line locally, put classy ply pattern plate.

(2) the installation of compound floor

1, floor joining together

Floor of joining together wood needs alignment, planish. Ensure to gap does not produce between the floor. Bespread whole room can.

2, measure length of the line that play a base

The length of the line that play a base that each room area place need to be used varies, because this need has measured each local place,need the length that uses.

3, the cut of the line that play a base

After the length of the line that play a base that needs in place of affirmatory nice area, its cut.

4, the installation of the line that play a base

In the aperture that receives check of the line that play a base obligate.

5, processing of connect of the line that play a base

When cut plays crural line, need the appearance with two upright proportional make it, join together at will different two end with benefit so.

6, secure the line that play a base

the floor the hammer secures the line that play a base, those who make is fixed, loosen not easily.

7, does real wood floor install flow?

1, ground processing

When installing real wood floor board, we can check the area with horizontal feet first is level off, if the the earth's surface is rough, it is good that everybody can make the same score cement mortar or do as one pleases can make the same score cement mortar or do as one pleases configuration, its daub has make level on the ground. After ground make level, we still need to examine the flatness of the ground, clear ground impurity clean.

2, the ground draws a line

Real wood floor can use the means of keel laid, when construction we want the laid seat that a keel plays on preexistence ground. Everybody is OK wait according to the span between the laid direction of wooden floor, length, keel undertake the ground draws a line. General floor of a wood needs 3 keel, the span between keel cannot exceed 350 millimeter.

3, laid keel

Electric drill of big housekeeping money undertakes stiletto on the ground, its call aperture depth normally 25 millimeter above. Next we secure keel on the ground with nail. When laid keel, need to leave the span that has 5-10 millimeter between keel and metope. After keel laid is good, we still need to check bibcock is level off firm. If the house compares moisture, after keel laid is good, we can spread a moistureproof film on keel.

4, floor of laid real wood

We can undertake trying spreading to real wood floor first, summary coloured poor floor is put in room inconspicuous place, and have cut out unwanted material to real wood floor. Next we get on laid of real wood floor in keel, nail a gun to originally floor clench with gas. The floor should use the means of amlposition laid, and every laid 3-5 piece wooden floor issues a floor to level with respect to need examination wait a moment continuously.

5, laid plays crural line

After wooden floor has been spread, we undertake bore on metope and a place of strategic importance enters chock, had cut out the line that play a base next, use its put away nail to secure its go up in metope.

8, power like that does the floor install flow?

Power like that the installation of the floor makes good floor veins that stand out under the skin first, had done moistureproof and moth-proofing protection, clean sanitation to install a floor board completely

9, must nature wood floor install crural line?

Nature wood floor needs to install crural line, beautiful, prevent become loose.

10, does floor of 69 yuan of nature include installation?

Do not include installation, normal installation cost needs 30 yuan every are smooth

The charge: that floor of nature real wood installs? Delay Si of the  that risk  this し ? is fact of 12 yuan of; commonly the price that wooden floor installs charge to be equal to real wood floor is multiplied come with the area laid of calculative; floor and the installation of the line that play a base, every square metre probably 3 yuan of Qian Zun are right, additional, if be the word of real wood,the capable person that the line that play a base employs pledges, the price from 10-60 yuan differ, more commonly used is in 20-30 yuan between.